Anti-fog film FOGCITY EASY Enduro FCE003, universal for off-road helmet visors

FOGCITY EASY Fullface Enduro is an anti-fog film installed on the inside of a helmet shield/visor. The EASY series allows installation on almost any surface. windshield. Installation is simple: just stick the film to the shield. Thanks to the highest-quality film and effective edge sealing, moisture from exhaled air does not reach the shield, preventing fogging extremely well. How does the FogCity® EASY anti-fog film work?The film is made of high-quality material with moisture-absorbing properties. The mechanism is simple – it works like a sponge and therefore prevents fogging on the helmet visor surface. FOG-FREE RIDING FOR EVERYONE! FogCity® strives to make its products as accessible as possible.Believing that "clear vision" is a key element of riding safety, FogCity® aims to provide perfect visibility for all motorcyclists, with every helmet, everywhere.It stays. In accordance with this motto, the technology used is based on materials and techniques that best help combat fogged visors. OFFER INSTRUCTIONS ANTI-FOG FOGCITY® FILM Step 1: Close the helmet visor and press it as tightly as possible (image A).< strong >Step 2: Attach adhesive tape to the center of the visor from the outside. Mark the planned upper edge of the film and the exact center of the visor on the attached tape. Use a fineliner or marker that does not stick to the tape or leave marks on the coated visor underneath the tape (image B below).The upper edge of the film should be positioned at a height where it will not rub against the seal when opening and closing the visor during subsequent use.Step 3:Remove the visor from the helmet – follow the instructions provided by the manufacturer of your helmet model to avoid damaging it.< br \/>Then make sure the inside of the visor is thoroughly cleaned and remember that dirt and even the smallest dust particles will remain under the installed film for the rest of its "life".Step 4:Peel the FogCity® film away from the protective transport film. Gently fold the anti-fog film into a U shape. Hold the film by its edge without touching the adhesive surface. During this step, direct the self-adhesive side of the film toward the visor on which it will be installed (image D, left picture).Step 5:Center the film using the tape attached to the previously marked center of the visor and the slight V-shaped indentation in the center of the film (image E, opposite). The upper edge of the film must not extend above the maximum height of the anti-fog protector previously marked on the tape.Step 6:Start by placing the upper and lower edges of the film in the center of the visor. Then gently spread the film outward over the remaining part of the visor – do not press on the film. Make sure the film is centered as described in the previous step and that the entire adhesive edge is in contact with the visor. If the self-adhesive edge does not adhere to the glass at any point, carefully lift the left or right end of the film and place it back on the glass so that the self-adhesive strip adheres to the glass along its entire length.< br \/>Step 7: After placing the film in the correct position on the glass, gently press it along its edges, starting from the center toward the left and right.Step 8: Remove the tape from the outside of the visor on which you marked the visor center and the upper edge of the film.Reinstall the visor on the helmet (again following the helmet manufacturer's instructions). After installation, make sure you can open and close the helmet visor properly and freely. For best results, it is recommended to wait 24 hours before using the helmet again, allowing the adhesive securing the film to cure. CLEANING: The FogCity film and helmet visor should be cleaned only with very mild liquids, preferably lukewarm water and a soft, gentle damp cloth. Both elements should be allowed to dry naturally before using the helmet again.DO NOT USE CLEANING MATERIALS THAT MAY SCRATCH THE GLASS OR FILM. DO NOT USE LIQUIDS CONTAINING WAX, AMMONIA OR ALCOHOL. IMPORTANT:To prevent damage to the FogCity® film and the upper seal of the helmet windshield, be sure to leave sufficient space between the film and the upper edge of the glass; ideally, the minimum distance of the film from the upper edge of the visor depends on the specific helmet model; do not press the film against the visor's central film surface (an air cushion should be created between the film and the glass); only the outer, self-adhesive edge may be pressed. ABOUT FOGCITY® DO NOT LET ANYTHING DISTRACT YOUR VIEW! FogCity® says no to anything that makes your visor foggy. Inspired by the amazing but often fog-plagued city of San Francisco – not without reason also called the Fog City – this company has developed highly effective anti-fog films that can be easily adapted to almost any type and shape of visor. SAFETY FIRSTMost motorcyclists know what it feels like to have limited visibility because of a fogged visor. FogCity® was created by motorcycle enthusiasts who wanted to put an end to this phenomenon, which not only threatens safety but also takes away much of the pleasure of riding a motorcycle.

FOGCITY EASY Enduro FCE003 – anti-fog film, universal for off-road helmet visors